Cleantalk is run by Solution World of Clean Ltd, you can find our cleaning chemicals and carpet cleaning machines here - www.worldofclean.co.uk
Online Dilution Calculator Here >
Download this page in PDF format > >In very simple terms, it is an advanced, plant-derived, detergent and enzyme-free cleaning agent that breaks down soils and micro-organisms at a submolecular level. It is eco-friendly in production, transportation, use and disposal. All this yet it out-performs most conventional cleaning products.
You can still buy the original M-Power above and use it at the great 1:120 dilution rate.
If you want the same cleaning ability but with added benefit of virus protection, choose M-Power+ with a different formulation & 1:50 dilution rate.
Both products can be used on carpets, upholstery and hard surfaces. Always pre-test the carpet, fabric or surface before cleaning.
Spray enough M-Power down to thoroughly dampen all fibres. Allow a 10 minute dwell period, during which agitation may be used to increase the soil fragmentation.
In cases of heavy soiling/traffic lanes, additional agitation may be required and/or following the initial spray, over-spray the heavily soiled area a second time using approximately 25% of the original amount sprayed. Extract.
Original M-Power
Dilute 8.3ml per 1 litre with warm water (1:120) – you may find a syringe is useful for measuring.
M-Power+ (EN 14476 approved)
Dilute 20ml per 1 litre with warm water (1:50)
Original M-Power
Dilute 66ml per 1 litre of warm water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
M-Power+ (EN 14476 approved)
Dilute 160ml per 1 litre of warm water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Lightly pre-spray carpet & agitate with a Floormac or rotary brush, allow a dwell of 10 minutes.
Moisten the bonnet with M-power and clean with an even overlapping motion. When the bonnet becomes soiled, rinse and re-wet with M-power.
M-Power can also be added to the clean tank of your machine at 8ml per litre (1:120). The residual continuing effect of rinsing with M-Power will help to combat unwanted odours & stains after you have left the property.
M-Power+ can be used in fogging machines diluted at 1:50.
pH neutral in dilution with built in anti-foam and anti-stain protection, a fantastic safe & effective cleaner for upholstery & carpets.
Formulated using a unique blend of polymers, penetrants, builders, dispersants and antifoam agents.
Fabric 8 contains unique wetting agents which help penetrate fibres, these molecules attach to the dirt but not the fibres making rinsing a lot easier.
Benefits include accelerated drying times which reduce the risk of browning. The protective polymers also help prevent resoiling, leaving the fabric with a level of stain resistance.
The overall result is cleaner carpets or upholstery, much improved resistance to resoling, enhanced dry soil pick-up during subsequent vacuuming and easier cleaning in the future.
pH neutral in dilution with built-in anti-foam and soil retardant.
Eco-friendly & biodegradable, no detergents, enzymes or peroxides.
More thorough cleaning.
No tacky residues to produce rapid re-soiling.
Neutral formulation – no fibre damage, no need to acid rinse.
Reduced wick back and browning due to continuing encapsulation effect.
Shortened drying times over conventional products.
Enhanced dry soil pick-up.
Stain resistance.
Improved soil release during subsequent cleans.
Economical in use, saving you money. (standard dilution 1:100)
Versatility of formulation means it can also be used for spot stain removal, low moisture cleaning etc.
Suitable for all water tolerant fibres – natural or synthetic.
Always pre-test Fabric 8 in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer onto the carpet or fabric, allow 2-6 minutes contact time, agitate well using a pile brush or twin contra-rotating brush machine then rinse with plain water (hot, warm or even cold). For upholstery agitation use either a soft brush or microfiber mitt.
Normal Soiling: dilute 10-20ml per 1 litre with warm water (1:100 to 1:50)
Heavy soiling and restoration: dilute 30ml per 1 litre with warm water (1:33)
Dilute 120ml per 1 litre of warm water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Fabric 8 can also be added to the clean tank of your machine at 10ml per litre (1:100)
A premium heavy duty detergent free upholstery & carpet cleaning solution, safe, powerful and cost effective.
Heavy Duty easily cuts through grease, oil and heavily abused dirty carpets & fabrics.
The stain removal spectrum is immense and includes grease, drink stains, protein stains, paints, mustard, oils, ketchup, rust and much more.
Can be used on both carpets & upholstery.
Contains no brighteners, soaps, detergents or enzymes – no foam or sticky residues which cause re-soiling.
Very economical in use – just lightly pre-spray the surface.
Can be over-sprayed onto other pre-sprays if extra cleaning power is needed.
Does not affect anti-stain protectors such as Protect Nano or anti-static treatments.
The cleaning process is achieved by breaking the adhesion between the soil particles and the surface to be cleaned, without the use of enzymes or detergents. It is lightly sprayed directly to the surface to be cleaned, then brushed in well.
Simple & easy to use with fantastic results!
Can be used as a single product solution for all types of colourfast carpet and fabric cleaning, subject to pre-testing.
Always pre-test Heavy Duty in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Lightly pre-spray onto the carpet or fabric, agitate well using a pile brush or twin contra-rotating brush machine. For upholstery agitation use either a soft brush or microfiber mitt. No dwell time is required.
Dilute 25ml per 1 litre of cold or warm water (1:40).
Dilute 200ml per 1 litre of warm water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Dilute 25ml per 1 litre of cold or warm water (1:40).
Lightly pre-spray the carpet & agitate.
Moisten the bonnet pad with Heavy Duty and clean with an even overlapping motion. When the bonnet becomes soiled, rinse and re-wet with Heavy Duty.
For low-profile commercial carpets, use a rotary or oscillating pad machine with either a scrub or microfibre bonnet pad.
Post spray or rinse with Crystal Rinse or Final Phase if required.
SPM is a high performance multi-purpose carpet and upholstery cleaning agent that uses a detergent free solution to break down soiling. Boost your cleaning with the power of oxygen bubbles!
SPM saves you money, time and hassle, it’s a fantastic all round cleaning product for any fabric or carpet.
NEW – Dilution rate has been doubled!
Powerful Stain Remover.
Powerful Deodoriser.
Powerful Antimicrobial.
Makes whites and colours look brighter without the use of optical brighteners.
Super Fresh Atlantic Breeze Fragrance
SPM does not contain detergent, optical brighteners, enzymes, solvents, or caustic alkalis. SPM can be used as a single product solution for all types of carpet and fabric cleaning operations, subject to pre-testing.
Similar to our Solution Heavy Duty, but SPM also has a built in oxygenating additive which boosts the product. SPM utilises advanced detergent free technology, it contains a unique super wetting agent to aid penetration into fibres.
The cleaning process is achieved by breaking the adhesion between the soil particles and the surface to be cleaned, without the use of enzymes or detergents. It is lightly sprayed directly to the surface to be cleaned, then brushed in well.
The stain removal spectrum is immense and includes grease, drink stains, protein stains, paints, mustard, oil, ketchup, rust and much more.
For best results the product should be brushed in well, ideally with either a pile brush or CRB/rotary machine.
Can be used as a single product solution for all types of carpet and fabric cleaning operations, subject to pre-testing.
Always pre-test SPM in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Lightly pre-spray onto the carpet or fabric, agitate well using a pile brush or twin contra-rotating brush machine. For upholstery agitation use either a soft brush or microfiber mitt. SPM works on contact, no dwell time is required. Not for use in a portable rinse tank.
Mix 2-4 scoops per 5 litres of hot water depending on soiling.
Mix 4 scoops per 1 litre of hot water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Mix 10 scoops into 20 litres of hot water to make a metering concentrate. Set meter at 2-3 GPH.
Mix 1-2 scoops into 5 litres of hot water. Pre-spray, moisten bonnet with cleaning solution and clean with an even overlapping motion. When the bonnet becomes soiled, rinse and re-wet with cleaning solution.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Solvent Free, Heavy Duty Restoration Formula.
Nitro is a highly concentrated heavy duty pre-spray. Nitro uses an advanced cationic solvent-free formula for lifting spots, stains, carbon, grease, oil, soot, rubber and other deeply ingrained soils.
Ideally suited for use as a high performance pre-spray on carpets, upholstery, porous surfaces, hard surfaces and many other professional restoration applications.
Extremely effective pre-spray for heavily soiled carpets & fabrics.
Removes problematic dry soiling from soot & carbon fire residues.
Removes filtration draft marks on carpets, fabrics and other surfaces.
Contains a unique highly dynamic wetting agent & cationic formula, it works when other products fail.
Better penetration and soil releasing.
Less agitation required prior to rinsing.
Deodorises on application.
Can be used with Spark if required for an additional kick.
Always pre-test Nitro in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer onto the carpet or fabric, allow 2-6 minutes contact time, agitate well using a pile brush or twin contra-rotating brush machine then extract. For upholstery agitation use either a soft brush or microfiber mitt. Do not over wet.
Normal soiling: dilute 10-20ml per 1 litre with warm water (1:100 to 1:50)
Heavy soiling and restoration: dilute 30-40ml per 1 litre with warm water (1:25)
Dilute 120ml per 1 litre of warm water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Specifically made for cleaning heavy soiling, black top restaurant carpets and anything that requires some serious firepower, Shockwave is the ultimate choice for when the going gets tough!
New – clean fresh fragrance with a tropical twist.
Designed as a complete formulation for the cleaning of heavy grease and organic soiling, Shockwave also contains encapsulating enzymes to digest soils, odours, food stains, blood and more. Protein stains are easily dealt with.
Unique & highly effective, its instant action grease breaking formulation will save you both time & money.
Fantastic on:
Heavy trodden in soiling.
Heavy greasy carpets.
Urine.
Food based grease and oil.
Blood.
Faeces.
Milk and egg based stains.
Always pre-test Shockwave in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer to the carpet or fabric and allow some dwell time – agitation can be applied during this contact period if required.
Mix 1-2 scoops per 1 litre of hot water depending on soiling.
Mix 8 scoops per 1 litre of hot water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Mix 14 scoops into 20 litres of hot water to make a metering concentrate. Set meter at 3 GPH.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Highly effective on a wide range of heavy soiling and stains. Instant results with little to no agitation or dwell time needed.
Ultra low residue, can be used as a pre-spray or rinse.
Maximum power and economical in use.
Instant results without agitation.
High alkaline detergent pre-spray.
Can also be used as a rinse in truckmounts or portables.
Powerful grease-breaking formula.
Outstanding results on heavily soiled carpets.
Economical powdered formulation (3p per Litre)
Pleasant fragrance.
Blaze is an ultra concentrated high performance extraction detergent giving you maximum results whilst being very economical in use, saves you both time & money.
Blaze contains a unique blend of solvents, wetting agents and balanced surfactants to produce a highly effective pre-spray. Acts quickly to emulsify and dissolve the heaviest of soil loading. Fast acting also allows for less dwell time producing outstanding results on heavily soiled commercial or domestic carpets.
Always pre-test Blaze in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer to the carpet or fabric, agitate if required then extract. Do not allow to dry.
Mix 1-2 scoops per 5 litres of hot water depending on soiling.
Mix 1½ scoops per 1 litre of hot water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Mix 8 scoops into 20 litres of hot water to make a metering concentrate. Set meter at 2-3 GPH.
Blaze can also be used to boost your cleaning power via rinsing, add it to your rinse tank at:
½-1 scoop per 5 litres if you’re also pre-spraying.
1-2 scoops per 5 litres as a standalone rinse.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Lemon Vibe is a ultra concentrated powdered citrus pre-spray with added solvent cleaning boosters.
As a fast acting pre-spray and degreaser, it works on contact breaking down and dissolving heavy build up from a wide range of soils & stains.
Literally zero dwell time required, works instantly saving you money & time!
Contains a powerful blend of alkaline cleaning agents and surfactants that quickly dissolve and emulsifies even the heaviest of soils. Does not contain enzymes but other active elements.
An amazingly versatile formulation, ideal for heavily soiled situations and neglected carpets, as well as heavy traffic areas and environments like pubs and restaurants.
Lemon Vibe has a pleasant citrus fragrance that leaves a fresh clean aroma to the room without being overpowering.
Being a super concentrated powder it will save you time & money. Readily dissolves quickly and easily.
Always pre-test Lemon Vibe in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer to the carpet or fabric, agitate if required then extract. Do not allow to dry.
Mix 1-2 scoops per 5 litres of hot water depending on soiling.
Mix 1½ scoops per 1 litre of hot water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Mix 8 scoops into 20 litres of hot water to make a metering concentrate. Set meter at 2-3 GPH.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Ever wished your pre-spray was stronger and worked faster? Spark can be used by itself as a performance pre-spray or as a powerful booster when mixed with other pre-sprays on multiple surfaces.
Adding a little Spark to your pre-sprays will supercharge your cleaning, making them more effective. It’s a unique heavy hitter with serious cleaning power, save money today with two products in one!
Maximum power and economical in use.
High alkaline detergent pre-spray.
Powerful grease-breaking formula.
Outstanding results on heavily soiled carpets – works on all types of soiling on multiple surfaces.
Economical powdered formulation (3p per Litre)
Pleasant light fragrance.
Accelerates any alkaline or neutral cleaning chemical – making them work much harder.
Boosts cleaning power making cleaning cheaper, easier & faster.
Safe on carpets & upholstery (subject to pre testing)
Improves performance of floor strippers and hard surface cleaners.
Get serious with your cleaning, add some spark and ignite to your cleaning today!
Always pre-test Spark in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Apply by sprayer to the carpet or fabric and allow some dwell time – agitation can be applied during this contact period if required.
Mix 1-2 scoops per 5 litres of hot water depending on soiling.
Use as a standalone pre-spray or mix with other chemicals as a booster. Not for use in tank.
Mix 1½ scoops per 1 litre of hot water (1:8 dilution). Adjust the sprayer to 1:4 for heavily soiled areas.
Mix 8 scoops into 20 litres of hot water to make a metering concentrate. Set meter at 2-3 GPH.
Post spray or rinse with Crystal Rinse or Final Phase if required.
Hydro202 is a highly advanced low moisture encapsulation carpet and upholstery cleaning solution. It packs a powerful punch with extra cleaning power provided by a newly developed biodegradable oxidiser. The oxidiser also brightens the carpets appearance to really impress your customers.
Developed using synthetically blended molecules which produce outstanding levels of cleaning even in the worst of conditions.
After cleaning the carpet will benefit from Hydro 202’s unique soil retardant & anti-soiling properties, helping to protect your clients carpets keeping them cleaner and healthier than ever before.
Hydro202 will also deodorise the fabric or carpet, leaving it fresh, clean, and smelling great.
Dilute up to 40 ml per 1 litre of warm water depending on the degree of soiling (1:25).
Can be used with all bonnet cleaning systems, including heated.
Thoroughly vacuum the carpet, pre-spray both the cleaning pad/bonnet, and the area to be cleaned.
Work in sections using a wringer bucket to clean the bonnets when fully loaded with soiling.
Always keep the cleaning pads/bonnets moist during cleaning. Using a TM3/Pro35 with renovator trays can be beneficial after the vacuuming stage.
Hydro202 can be used as a low moisture encapsulation foaming agent.
Whisk up in a bucket or use a foaming sprayer.
Lightly apply via hand mitt, foam sprayer or sponge, agitate in then terry towel off.
Fusion Clean is a concentrated encapsulation cleaning solution with built in anti-soil & anti stain protection properties. Ideal for bonnet cleaning or low moisture cleaning.
Synthetically blended molecules produce outstanding levels of low moisture encapsulation with carpet & upholstery cleaning.
This amazing product is detergent free containing natural plant extracts and uses new technology with built in anti-stain & anti-soil properties.
Fusion Clean will keep your clients carpets cleaner and healthier for even longer and at the same time naturally deodorise the cleaned areas leaving a fresh clean aroma.
Can be used with all bonneting systems including heated bonnet systems.
Can be used as a stand alone encapsulating solution with endless uses on upholstery and carpets.
Dilute up to 40 ml per 1 litre of water depending on the degree of soiling (1:25).
Can be used with all bonnet cleaning systems, including heated.
Thoroughly vacuum the carpet, pre-spray both the cleaning pad/bonnet, and the area to be cleaned.
Work in sections, use a wringer bucket to clean the bonnets when fully loaded with soiling.
Always keep the cleaning pads/bonnets moist during cleaning. Using a TM3/Pro35 with renovator trays can be beneficial after the vacuuming stage.
Fusion Clean can be used as a low moisture encapsulation foaming agent.
Whisk up in a bucket or use a foaming sprayer.
Lightly apply via hand mitt, foam sprayer or sponge, agitate in then terry towel off.
Can also be pre mixed and applied via a foamer/or beat to a foam and applied using a Microfiber hand mit agitated and towelled off.
Ideal for low moisture encapsulation cleaning of upholstery, carpets & pigmented leather.
Using Fabric Foam is an easy way to safely clean suites or any fabric, start earning some extra money today instead of turning them down!
Fabric Foam is a concentrated encapsulation cleaning solution with built in anti-soil & anti stain protection properties. It contains active soil repellents to help fibres stay cleaner for longer with “easier next time cleaning”.
Contains unique penetrating wetting agents and a blend of fast acting stain removers to deal with the most stubborn staining, it will also naturally deodorise the cleaned areas leaving a fresh clean citrus aroma.
Designed for use with our rechargeable E-Foam sprayer for low moisture cleaning of carpets & fabrics, including pigmented leather. Can be applied to vertical surfaces.
Bonnet systems – can be used as stand-alone encapsulating solution with endless uses on upholstery and carpets.
Always pre-test Fabric Foam in an inconspicuous area for colour fastness prior to use. Shake or stir well for complete mixing.
Dilute 30 – 60ml per 1 litre of warm water. When using our E-Foam sprayer just add one full mini mixing jug to it. (included with the sprayer)
Dry vacuum thoroughly.
Using the E-Foam sprayer apply the foam evenly to the item to be cleaned.
Agitate the foam into the upholstery with either a tampico upholstery brush / microfibre hand mitt or rotary drill brush.
Allow a few minutes to dwell then using a white terry towel remove the surface residue.
For added results vacuum again when dry.
Dry vacuum thoroughly.
Pre-spray the carpet with Fabric Foam.
Moisten the bonnet with Fabric Foam and clean with an even overlapping motion. When the bonnet becomes soiled, rinse and re-wet with fabric Foam.
A highly refined non-aromatic dry cleaning solvent developed as a safe alternative to 1,1,1, Trichloroethane solvents.
Can be used to dry clean curtains, upholstery and other water sensitive fabrics.
Safety Solvent Cleaner does not contain any ozone depletants. It’s safe to use on metals, alloys, electric/electronic components, plastics, painted surfaces including chlorinated rubber finishes.
Thoroughly vacuum the fabric to be cleaned, apply the solvent via light misting or with a coral sponge, cloth, hand mitt or our applicator brush.
Agitate with a soft upholstery brush or mitt.
Remove the dirt & soiling with clean terry towels or microfiber clothes.
Finish and set the pile with a boffin brush.
Always work in sections going seam to seam.
Can also be used in an ultrasonic bath or dip tank or in dry solvent cleaning machines.
Allow to dry naturally, or blow dry with air.
Prevent permanent & unsightly stains before they even happen! Easy to apply stain protection for common household fabrics & carpets.
Protect Nano is an advanced fabric & carpet stain protector, it contains a water based solution of fluoro-chemical nano-particles which cures in air to form a water and oil repellent barrier on porous surfaces.
Unlike most water-based fluoro-chemicals, Protect Nano does not require high temperature curing to give optimum oil and water repellency.
Protect Nano is designed to give lasting stain protection on carpets, fabrics, stone, tiles and other porous surfaces (not suitable for silk). Suitable training in its use forms part of our training courses.
Protect Nano protects against penetration by oil or water based contaminants making the cleaning of surfaces very easy – most protected spills can simply be wiped or mopped away.
The protection is long lasting but will be reduced over time depending on wear, traffic and cleaning regime. Aggressive cleaners should not be required on Protect Nano, protected surfaces and their use will reduce the lifetime of the protective effects.
1:1 – Dilute 1 litre of Protect Nano with 1 litre of water.
Apply using a pressure sprayer, similar to a garden type sprayer using a 500050 T-Jet fan type nozzle to a clean surface.
Pre-dampen fabrics with a light spray of plain water if the item has not been cleaned recently or is dry.
Apply 1 coat east to west, after 10 minutes apply a second coat north to south – DO NOT BRUSH IN, leave to dry.
Apply evenly at the rate of 50-100ml per m2, depending on the absorbency of the surface.
Only spray in conditions of good ventilation. The spray operator and anyone in the vicinity should avoid inhalation of the spray mist and suitable protective masks are recommended.
Drying time will be longer than with solvent based sprays, this can be accelerated by the use of zone heating and forced ventilation.